Asus manufactures a variety of routers for user convenience and access to the internet. But, the Asus router DHCP error can lead to various problems. In addition to that, it can also restrict you from accessing the internet. So, you have to understand the facts about DHCP. Furthermore, you have to dig deep into the causes and then move on to the solutions.
DHCP is the Dynamic Host Configuration Protocol, and it manages your internet connection. In addition to that, the DHCP also automates configuring the connected devices to the router that is present on the same IP address network.
There are two reasons for this issue – The improper configuration of your system or any connected device restricts the DHCP server to assign an IP address. The other is the improper configuration of the master DHCP server. So, how about getting along with the solutions as soon as possible to fix the issue.
Interchanging the Frequency of the DHCP Query
While configuring the system, it’s obvious that you can make an error regarding the DHCP. In general, the DHCP mode is set to normal. Sometimes, you can configure it to any other modes, let’s say Aggressive.
The Aggressive mode of the router will work normally. On changing the mode, the device will incorporate the changes. The router will send the DHCP request to the master server, and it will take not more than 5 minutes.
Initiating the SH3 Values
Asus router DHCP error might take place due to the occurrence of the poor signal or network frequency. Therefore, the boost of the signal strength will be necessary. With the SH3 values, you can increase the strength of the network signal, and different network IPs have different SH3 values.
In general, the default value of the SH3 is 192.168.100.1. Make the necessary changes as per requirement. But, remember – The gateway address of the WAN looks similar to the SH3 value. So, be careful about that.
Reset the Modem
It seems that you are using a Modem along with the router. The modem generally translates the network connection and brings it to the router. Since the Asus router DHCP error occurs, resetting the modem may come in handy.
Most experts say that it is a logical method and you must try it. Turn off the router and locate the reset button of the modem. Press and hold it for a few seconds. After that, you have to reconfigure the router once again. If you are not using the modem, your router might act as both. So, the process of reset is the same.
Change of Network Bands
Nearly every router has two network bands – 2.4 GHz and 5 GHz. If the 2.4 GHz band is active and facing the Asus router DHCP error, then changing it to 5GHz is a legitimate idea. Navigate to the Router dashboard and select the Network Settings. Find out the network bands and select the 5 GHz. Save the changes and check whether the issue is persisting or not.
Get a Provisional Signal
Ask your ISP/network administrator to send a provisional signal. If you get the signal correctly, your DHCP server is working fine. Other than that, the Asus router DHCP error is taking place. The provisional signals are the key factors that will perform a certain type of reset to the dynamic network IP and the DHCP.
Check the Network Resolution Settings
The network resolution settings play one of the most important roles in DHCP manipulation. During the ongoing Asus router DHCP error, it’s a good idea to change the value or otherwise, the error might continue. Let’s take it as an example – The value is 380.68-4. Now, change the value to 380.69. In some cases, you may have to change the 380 to 382.
Eliminate the Data Packet Losses
The data packet loss of your network connection can easily lead to the Asus router DHCP error. In this type of scenario, you cannot do much. Check the ping with the Command Prompt’s help and the network IP address. You will find the network request timed out after some time. Call the ISP and ask them to check and resolve the issue. Hopefully, this will help you to eliminate the ongoing problem.
Reset the Network Adapter
Resetting the network adapter will delete all the desired settings. Navigate to the settings or control panel and move on to the network and security. You will find the WAN and LAN adapter. Right-click on the adapter and disable it. After some time, enable both the adapters.
