netgear router firmware error

5 Methods to Fix NetGear Router Firmware Error

Netgear routers are one of the best network devices in the cyber world. The user interface is attractive and easy to use. Every router has its firmware that helps regulate and manipulate the connected devices. If the firmware faces any issues like NetGear Router Firmware Error, then the entire device will malfunction. 

A few users have suggested that the restart of the router might work to fix the problem. Yes, it will, but for a short span of time. Ultimately, the backbone of a router is firmware. If the firmware faces any error, the router can’t work properly. Malware effect, improper firmware installation, outdated router hardware can be possible reasons. 

Let’s Try the Solutions

Here are the effective solutions that will help you to fix the issue. Try to go through them carefully before performing. 

Solution 1: Force Restart the Router 

Turning off the electrical socket board switch is the normal way to restart the router. But, when the Netgear router firmware error occurs, you need to restart the device forcefully. First, plug out the Ethernet cable – after that, plug out the power cord. 

The device will turn off. Keep it in that state for a couple of minutes. Re-attach all the cables and cords which will power up the router. Now, check whether you are receiving the error message or not. 

Solution 2: Download the Correct Firmware Package File

Always visit the Netgear official support page to find out where you can download the package file. Make sure you choose the correct system compatible OS that you are using. In addition to that, selecting the correct bit version is also important. 

After the package download is complete, extract the file completely. Don’t interrupt the extraction process in-between. Install the package file and restart the router; it may not show the error message again. 

Solution 3: Verify the Internet Connection 

The Netgear router firmware error occurs when the network device doesn’t get its desired bandwidth. Therefore, verifying the internet connection is important. Check the ping and ensure there is no loss of data packets. 

After that, choose a good website and test the bandwidth. This will let you know the upload and download speed. If the download speed is less than upload, there are still background programs running. And, you must close them to save bandwidth. 

Solution 4: Close the Background Programs

It seems that you are sure about the excess network consumption of several background programs. Open the Task Manager and carefully notice the amount of data consumed by the list on ongoing processes. Only close those programs that are consuming the greater amount of bandwidth. Surely, this will fix the Netgear router firmware error. 

Solution 5: Avoid Interruptions

As usual, you know how to update the firmware. When the download goes on, never interrupt it because it can corrupt the package file. On the other hand, after uploading the package file to the Router Management page, you restart the router. During this process, try to avoid any type of interruptions. Else the new firmware will not get installed properly. 

Let’s Troubleshoot

To counter the Netgear router firmware error, you need to perform two types of troubleshooting processes – Basic and advanced. Let’s start with the Basic one first, and then you will move on to the Advanced. 

Basic Troubleshooting

Make sure that the power cord is not facing any wear and tear. Other than that, disable any type of active proxy while the router firmware is under the installation process. If any extenders are available, make sure that it is configured correctly. 

Lastly, scan your computer and eliminate any viruses. Also, make sure that you are using the static IP address to avoid the Netgear router firmware error in the future. 

Advanced Troubleshooting 

The advanced troubleshooting process involves the installation of an application. If you face the Netgear router firmware error while installing the firmware package directly, then here is an excellent process. 

Download and then install the Netgear firmware updater on your computer. After that, download the TFTP application too. Connect the main Ethernet cable to the extender and open the TFTP application if you have an extender. 

Select the LAN adapter. In the section of Host, type the router/extender IP address. If you don’t know either of them, check the router/extender package kit or user manual. Now, download the latest firmware file. You don’t have to upload any type of files to the dashboard in this process. When done, disconnect all the Ethernet cables and restart both devices.

Leave a Reply

Your email address will not be published.